Basic Switch Configuration Guide with Examples
This tutorial explains basic switch configuration commands in detail with examples. Configuration and commands explained in this tutorial are essential commands to manage a Cisco switch effectively. Learn how to configure and manage a Cisco Switch step by step with this basic switch commands and configuration guide.
To explain basic switch configuration commands, I will use packet tracer network simulator software. You can use any network simulator software or can use a real Cisco switch to follow this guide. There is no difference in output as long as your selected software contains the commands explained in this tutorial.
Create a practice lab as shown in following figure or download this pre-created practice lab and load in packet tracer
If require, you can download the latest as well as earlier version of Packet Tracer from here. Download Packet Tracer
In this topology
- Two 2960 Series switches are used.
- Switch1 (Interfarce Gig1/1) is connected with Switch2 (Interface Gig1/1) via cross cable.
- Switch1 has two PCs connected on interfaces Eth0/1 and Eth0/2 via straight through cable.
- Same as switch1, Switch2 also has two PCs connected on its interfaces Eth0/1 and Eth0/2.
- IP address is configured on all PCs PC0 (192.168.1.1/24), PC1 (192.168.1.2/24), PC2 (192.168.1.3/24), PC3 (192.168.1.4/24).
Click Switch1 and click CLI menu item and press Enter Key
Navigating between different switch command modes
Cisco switches run on proprietary OS known as Cisco IOS. IOS is a group of commands used for monitoring, configuring and maintaining cisco devices. For security and easy administration, IOS commands are divided in the set of different command modes. Each command mode has its own set of commands. Which commands are available to use, depend upon the mode we are in.
Following table lists necessary commands to navigate between different IOS modes with examples.
|Mode||Purpose||Prompt||Command to enter||Command to exit|
|User EXEC||Allow you to connect with remote devices, perform basic tests, temporary change terminal setting and list system information||Router >||Default mode after booting. Login with password, if configured.||Use exit command|
|Privileged EXEC||Allow you to set operating parameters. It also includes high level testing and list commands like show, copy and debug.||Router #||Use enable command from user exec mode||Use exit command|
|Global Configuration||Contain commands those affect the entire system||Router(config)#||Use configure terminal command from privileged exec mode||Use exit command|
|Interface Configuration||Contain commands those modify the operation of an interface||Router(config-if)#||Use interface type number command from global configuration mode||Use exit command to return in global configuration mode|
|Sub-Interface Configuration||Configure or modify the virtual interface created from physical interface||Router(config-subif)||Use interface type sub interface number command from global configuration mode or interface configure mode||Use exit to return in previous mode. Use end command to return in privileged exec mode.|
|Setup||Used by router to create initial configuration, if running configuration is not present||Parameter[Parameter value]:||Router will automatically insert in this mode if running configuration is not present||Press CTRL+C to abort. Type Yes to save configuration, or No to exit without saving when asked in the end of setup.|
|ROMMON||If router automatically enter in this mode, then it indicates that it fails to locate a valid IOS image. Manual entrance in this mode Allow you to perform low-level diagnostics.||ROMMON>||Enter reload command from privileged exec mode. Press CTRL + C key combination during the first 60 seconds of booting process||Use exit command.|
How to get help on Cisco Switch command mode
Switch provides two types of context sensitive help, word help and command syntax help.
Word help is used to get a list of available commands that begin with a specific letter. For example if we know that our command begins with letter e, we can hit enter key after typing e? at command prompt. It will list all possible commands that begin with letter e.
We can list all available commands, if we don't know the initials of our command. For example to list all available commands at User exec mode, just type ? at command prompt and hit enter key.
Command syntax help
Command syntax help can be used to get the list of keyword, commands, or parameters that are available starting with the keywords that we had already entered. Enter ? (Question mark) after hitting Space key and prompt will return with the list of available command options. For example to know the parameters required by show ip command type show ip ? and prompt will return with all associate parameters. If prompt returns with <CR> only as an option, that means switch does not need any additional parameters to complete the command. You can execute the command in current condition.
How to set name on switch
Switch name can be set from global configuration mode. Use hostname [desired hostname] command to set name on switch.
How to set password on a Catalyst switch
Passwords are used to restrict physical access to switch. Cisco switch supports console line for local login and VTYs for remote login. All supported lines need be secure for User Exec mode. For example if you have secured VTYs line leaving console line unsecure, an intruder can take advantage of this situation in connecting with device. Once you are connected with device, all remaining authentication are same. No separate configuration is required for further modes.
Password can be set from their respective line mode. Enter in line mode from global configuration mode.
VTY term stand for virtual terminal such as telnet or SSH. Switch may support up to thousand VTYs lines. By default first five (0 - 4) lines are enabled. If we need more lines, we have to enable them manually. 2960 Series switch supports 16 lines. We can set a separate password for each line, for that we have to specify the number of line. In our example we set a common password for all lines.
Above method is good for small companies, where numbers of network administrators are very few. In above method we have to share password between all administrators. Switch supports both local and remote server authentication. Remote server authentication is a complex process and not included in any entry level exams. For this article I am also skipping remote server method. In local database authentication method switch allows us to set a separate password for each user. Two global configuration commands are used to set local user database.
Switch(config)#username [Username] password[test123] Or Switch(config)#username [Username] secret[test123]
Both commands do same job. Advantage of using secret option over password option is that in secret option password is stored in MD5 encryption format while in password option password is stored in plain text format.
Along with User Exec mode we can also secure Privilege Exec mode. Two commands are available for it.
Switch(config)# enable password Privilege_EXEC_password or Switch(config)# enable secret Privilege_EXEC_password
Again as I mentioned earlier, password stored with secret command is encrypted while password stored with password command remains in plain text. You only need to use single command. If you would use both commands as I did, enable secret command would automatically replace the enable password command.
How to reset switch to factory defaults
During the practice several times we have to reset switch to factory defaults. Make sure you don't run following commands in production environment unless you understand their effect clearly. Following commands will erase all configurations. In production environment you should always takes backup before removing configurations. In LAB environment we can skip backup process.
Switch>enable Switch#delete flash:vlan.dat Delete filename [vlan.dat]? [Press Enter Key] Delete flash:vlan.dat? [confirm] [ Reconfirm by pressing enter key] Switch#erase startup-config Switch#reload
How to set IP address in Switch
IP address is the address of device in network. Switch allows us to set IP address on interface level. IP address assigned on interface is used to manage that particular interface. To manage entire switch we have to assign IP address to VLAN1( Default VLAN of switch). We also have to set default gateway IP address from global configuration mode. In following example we would assign IP 172.16.10.2 255.255.255.0 to VLAN1 and set default gateway to 172.16.10.1.
Switch>enable Switch#configure terminal Switch(config)#interface vlan1 Switch(config-if)#ip address 172.16.10.2 255.255.255.0 Switch(config-if)#exit Switch(config)#ip default-gateway 172.16.10.1
How to set interface description
Switches have several interfaces. Adding description to interface is a good habit. It may help you in finding correct interface. In following example we would add description Development VLAN to interface FastEthernet 0/1.
Switch(config)#interface fastethernet 0/1 Switch(config-if)#description Development VLAN
How to clear mac address table
Switch stores MAC addresses in MAC address table. Gradually it could be full. Once it full, switch automatically starts removing old entries. You can also clear these tables manually from privileged exec mode. To delete all entries use following command
switch#clear mac address-table
To delete only dynamic entries use
switch#clear mac address-table dynamic
How to add static MAC address in CAM table
For security purpose sometime we have to add mac address in CAM table manually. To add static MAC address in CAM table use following command
Switch(config)#mac address-table static aaaa.aaaa.aaaa vlan 1 interface fastethernet 0/1
In above command we entered an entry for static MAC address aaaa.aaaa.aaaa assigned to FastEnternet 0/1 with default VLAN1.
How to save running configuration in switch
Switch keeps all running configuration in RAM. All data from RAM is erased when we turned off the device. To save running configuration use following command
Switch#copy running-config startup-config
How to set duplex mode
Switch automatically adjust duplex mode depending upon remote device. We could change this mode with any of other supported mode. For example to force switch to use full duplex mode use
Switch(config)# #interface fastethernet 0/1 Switch(config-if)#duplex full
Switch(config)# #interface fastethernet 0/1 Switch(config-if)#duplex half
show version command provides general information about device including its model number, type of interfaces, its software version, configuration settings, location of IOS and configuration files and available memories.
Switch stores MAC address of devices those are attached with its interfaces in CAM table. We can use show mac-address-table command to list all learned devices. Switch uses this table to make forward decision.
Switch stores IOS image file in flash memory. show flash command will list the content of flash memory. This command is useful to get information about IOS file and available memory space in flash.
Configuration parameter values are created, stored, updated and deleted from running configuration. Running configuration is stored in RAM. We can use show running-config command to view the running configuration.
Any configuration stored in RAM is erased when devices is turned off. We can save running configuration in NVRAM. If we have saved running configuration in NVRAM, it would be automatically loaded back in RAM from NVRAM during the next boot. As switch load this configuration back in RAM in startup of device, at NVRAM it is known as startup-config.
show vlan command will display the VLANs. For administrative purpose, switch automatically create VLAN 1 and assign all its interfaces to it. You can create custom VLANs from global configuration mode and then assign them to interfaces.
show interface command displays information about interfaces. Without argument it would list all interfaces. To get information about specific interface we need to pass its interface number as an argument. For example to view details about FastEthernet 0/1, use show interface fastethernet 0/1.
First line from output provides information about the status of interface.
FastEthernet0/1 is up, line protocol is up ( connected)
The first up indicates the status of the physical layer, and the second up indicates to the status of the data link layer.
Possible interface status
- up and up :- Interface is operational.
- up and down :- Its data link layer problem.
- down and down :- Its physical layer problem.
- Administratively down and down :- Interface is disabled with shutdown command.
Possible values for physical layer status
- Up :- Switch is sensing physical layer signal.
- Down :- Switch is not sensing physical layer signal. Possible reasons could be cable is not connected, wrong cable type is used and remote end device is turned off.
- Administratively down :- Interface is disabled by using shutdown command.
Possible values for data link layer status
- Up :- The data link layer is operational.
- Down :- The data link layer is not operational. Possible reasons could be a disabled physical layer, missed keep alives on a serial link, no clocking or an incorrect encapsulation type.
show ip interface brief
show ip interface brief is a extremely useful command to get quick overview of all interfaces on switch. It lists their status including IP address and protocol.
That’s all for this article.
By ComputerNetworkingNotes Updated on 2018-08-06 00:41:51 IST
- Cisco IOS Naming Convention Explained with Examples
- OSPF LSA Types and LSA Flooding Explained
- IGP, EGP, and Autonomous System Explained
- OSPF Fundamental Terminology Explained
- OSPF Features, Advantages, Disadvantages
- Administrative Distance (AD) Explained
- Types of Access Control Lists Explained
- Cisco IOS Backup and Restore Process Step By Step Guide
- RIP Protocol configuration Guide with Examples